Jump to content

ED250 Pendolino - Train brake handle difficult to control


Recommended Posts

As per the description. The old Pendolino brake handle was bad enough, it's even worse now where from running position to actually to get it into an apply state requires a heavy double tap which either then puts into 25% brake or full on 100% anchor out of the window brake with cups flying across the buffet car!

Server: N/A
Build: 24/11/2023 15:21

  • I agree 4
Link to comment
Share on other sites

Only having to do short keypresses to move the lever between positions would make it way easier imo. Then you'd roughly know where the lever is based on the number of presses made. Wouldn't have to look at the lever as much either, just stick with monitoring the gauges and verify the changes.

However, does the real deal have fixed positions or does it have fine control too? I've noticed the lever in SimRail can end up in between positions, although not very gracefully so I've stuck with trying to get it into a position for the most part.

Link to comment
Share on other sites

Same here, the problem is that you can't say I press the brake+ key 1 or2 times, and it switches from Cutoff to Fill or from Fill to Drive. It also depends how long you press. So you always have to look on the brake lever when using it to see if it has moved to the next position or not.  But my train Instructor always told me to watch the route and the instruments, especially when approaching a signal where I maybe have to stop. 🙄

Additionaly there's no feedback in the form of a certain click-sound between the lever positions. It feels like a brake lever of an old '50s Locomotive inside a Hightec train.

But nevertheless, I love this locomotive!!

Link to comment
Share on other sites

  • 1 month later...

Yea had the same problem with the ne76 already thought I was crazy

And got a 5 min delay on just the "very Easy " tutorial Mission

Meanwhile I got like 4 min ahead of schedule in the traxx with the coal load which is supposed to be hard

And there is also a significant delay between brakes off and getting power again is that really supposed to be that way?

Edited by meki98
Link to comment
Share on other sites

vor 5 Stunden schrieb meki98:

Yea had the same problem with the ne76 already thought I was crazy

And got a 5 min delay on just the "very Easy " tutorial Mission

Meanwhile I got like 4 min ahead of schedule in the traxx with the coal load which is supposed to be hard

And there is also a significant delay between brakes off and getting power again is that really supposed to be that way?

well how longer the train so longer it need till the brakes are released again  🙂

Link to comment
Share on other sites

  • 1 month later...
On 1/15/2024 at 7:38 PM, Fightdrug said:

well how longer the train so longer it need till the brakes are released again  🙂

Problem is the brakes are off just the power isn't coming back after the brake pressure is Reset 

 

I miss the controls of msts were the buttons did control Prozenteges of the brakes so there wasn't a risk of accidentally getting the emergency brake 

Edited by meki98
Link to comment
Share on other sites

vor 10 Minuten schrieb meki98:

Problem is the brakes are off just the power isn't coming back after the brake pressure is Reset 

I miss the controls of msts were the buttons did control Prozenteges of the brakes so there wasn't a risk of accidentally getting the emergency brake 

do you had the speed leveler back to ,,0" after release the brakes 🤔 the traxx and the dragon dont will give any power before the speed leveler is back in neutral positon

Link to comment
Share on other sites

3 minutes ago, Fightdrug said:

do you had the speed leveler back to ,,0" after release the brakes 🤔 the traxx and the dragon dont will give any power before the speed leveler is back in neutral positon

I do that a few times until the power eventually comes back

Link to comment
Share on other sites

vor 30 Minuten schrieb meki98:

I do that a few times until the power eventually comes back

mostly in the traxx the brakes show released in the hud while it isnt so you can see that in the traxx on the far right brake needle it goes slowly back to 0 when it reach the 0 you can give power again before that the train brakes are not complete empty, here is a photo from the needle i mean 20240220130550_1.thumb.jpg.3664957b82b542509e41585cc250ed04.jpg

  • I agree 1
Link to comment
Share on other sites

vor 13 Stunden schrieb meki98:

that needle dosent move if i dont get a emergency brake

Its the loco break. The needle moves when you apply the loco break or the train comes to a stand still. For example holding in front of a Red Signal

Link to comment
Share on other sites

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

Terms of Use Privacy Policy